Class 12 Physics · Chapter 14 · 97 questions · pyqhub.org

Q0012026 · 2025 · 2024 · 2023 · 2022–23 · 2022 · 2020 · 2019 · 2015 · 2010Board · Sample paperDiode bias and I–V characteristics

Draw circuits to measure the forward and reverse I–V characteristics of a silicon diode and sketch the characteristics. Explain knee voltage, reverse saturation current, minority-carrier injection and breakdown voltage. What information can the curves provide?

Check answer and diagram
Forward bias: p/anode to positive, n/cathode to negative, with a current-limiting resistor and milliammeter in series; voltmeter across the diode. Reverse the diode and use a microammeter for reverse characteristics. Forward current rises rapidly beyond the approximate knee (about 0.7 V for silicon at ordinary currents, not a universal sharp threshold). Majority electrons and holes cross the junction and become minority carriers on the other side. Below reverse breakdown, thermally generated minority carriers give a small nearly constant current. Breakdown produces a steep current increase; the current must be limited. The curves show polarity, approximate knee/breakdown voltages and local slope dI/dV; dynamic resistance is dV/dI.
Q0022026Board1 markDiode bias and I–V characteristics

Forward voltage rises from 0.8 V to 1.0 V while diode current increases by 2 mA. Find its average dynamic resistance over that interval.

Check answer
r=ΔV/ΔI=0.2/0.002=100 Ω.
Q0032026Board1 markDiode bias and I–V characteristics

How should a sound ordinary junction diode behave in a multimeter resistance test in the two directions?

Check answer
It should show relatively low resistance in forward bias and high resistance in reverse bias, within the meter’s test range. A diode-test voltage reading is often a more useful practical test.
Q0052026BoardAdapted questionDiode circuits and numerical problems

Solve the two circuits shown. (a) For the 220 V RMS sinusoidal source, find the capacitor’s steady-state voltage after charging. Assume an ideal diode, initially uncharged capacitor, no load and negligible leakage. (b) Find V_AB in the 15 V circuit, treating its diode as ideal.

Check answer
(a) The capacitor charges to the positive peak, 220√2≈311 V. Its steady voltage is DC, whose RMS is also 311 V; it does not keep following a rectified sine without a discharge path. (b) D conducts, putting the two 10 Ω branches in parallel: 10∥10=5 Ω. This forms a divider with the upper 5 Ω; V_AB=15×5/(5+5)=7.5 V.
Q0062026Board3 marksDiode circuits and numerical problems

For the pictured network with V_AB=12 sin(100πt) V and ideal diodes, analyse the positive input half-cycle. Identify the conducting diode, draw the equivalent circuit and find the peak voltage across each resistor.

Check answer and diagram
With A positive, D₂ conducts and D₁ is reverse biased. Replace D₂ by a wire and D₁ by an open circuit. The 1 kΩ and 2 kΩ resistors form a series branch across 12 V, in parallel with the 3 kΩ branch. Peak voltages are 4 V across 1 kΩ, 8 V across 2 kΩ and 12 V across 3 kΩ. Current in the series branch flows R→P→B.
Q0082026Board3 marksEnergy bands

At a fixed temperature an intrinsic semiconductor has nᵢ=3×10⁸ m⁻³. After doping its hole density is 6×10¹⁰ m⁻³. Find electron density, identify the type and explain what weak doping does to the band diagram. Assume thermal equilibrium and nondegenerate doping.

Check answer
np=nᵢ² gives n=(3×10⁸)²/(6×10¹⁰)=1.5×10⁶ m⁻³. It is p-type, with acceptor impurities. Weak doping introduces acceptor levels just above the valence band; it does not simply replace the host band gap with the small acceptor-ionisation energy.
Q0092026BoardAdapted questionEnergy bands

Compare n-type and p-type samples of the same material, temperature and equal majority-carrier density, with negligible minority-carrier conduction. Assertion: the n-type sample has greater conductivity. Reason: electron mobility exceeds hole mobility in this material. Evaluate.

Check answer
Both true, and the reason explains the assertion: σ≈enμₑ or epμₕ. Equal density and μₑ>μₕ give σ_n>σ_p. Without matched concentrations the conductivity ordering is not determined by the labels n-type and p-type alone.
Q0102026Board1 markIntrinsic and extrinsic semiconductors

Which carrier-transport processes dominate junction current under forward bias and reverse bias, below breakdown?

Check answer
Forward: majority-carrier diffusion across the reduced barrier. Reverse: drift of thermally generated minority carriers. In the neutral regions, electric fields also drive the carriers through the external circuit.
Q0112026 · 2025 · 2024 · 2023 · 2022 · 2012BoardIntrinsic and extrinsic semiconductors

Give examples of dopants that produce p-type and n-type silicon. Explain the majority and minority carriers and whether either material has a net electric charge.

Check answer
Trivalent B, Al, Ga or In produce p-type: holes majority, electrons minority. Pentavalent P, As or Sb produce n-type: electrons majority, holes minority. Both remain electrically neutral overall: ionised acceptors balance excess holes, and positive donors balance excess electrons.
Q0122026 · 2025 · 2022 · 2018 · 2015 · 2008BoardIntrinsic and extrinsic semiconductors

Distinguish intrinsic and extrinsic semiconductors. Explain doping, donor/acceptor action and why a doped specimen can remain electrically neutral although n≠p.

Check answer
An intrinsic semiconductor is pure, with n=p=nᵢ. Extrinsic material is deliberately doped to control carrier density and conductivity; n-type has n≫p, p-type has p≫n. Donors supply electrons and become positive ions; acceptors take valence electrons, leaving holes and negative ions. These fixed ion charges balance the mobile charge, so unequal mobile carrier concentrations do not imply net charge. In the ordinary nondegenerate equilibrium regime np=nᵢ².
Q0132026BoardAdapted questionIntrinsic and extrinsic semiconductors

Semiconductor case: (i) Name a trivalent dopant for p-type silicon. (ii) If n=5×10²² m⁻³ and nᵢ=1.5×10¹⁶ m⁻³, find p. (iii) State the dominant junction-current mechanism under forward bias. (iv) Give the approximate silicon cut-in voltage, and the order of donor-ionisation energy in germanium. Assume thermal equilibrium.

Check answer
(i) Boron, for example. (ii) p=nᵢ²/n=4.5×10⁹ m⁻³. (iii) Diffusion of majority carriers across the junction, followed by minority-carrier injection. (iv) Roughly 0.7 V for silicon at typical currents; donor binding in Ge is of order 0.01 eV. Actual diode turn-on is gradual and temperature/current dependent.
Q0152026Board2 marksIntrinsic and extrinsic semiconductors

At fixed temperature nᵢ=5×10⁸ m⁻³ and doped electron density n=4×10¹² m⁻³. Find the hole density and semiconductor type in thermal equilibrium.

Check answer
p=nᵢ²/n=6.25×10⁴ m⁻³; the specimen is n-type.
Q0162026Board2 marksIntrinsic and extrinsic semiconductors

Silicon has 5×10²⁸ atoms m⁻³ and is doped with 1 ppm of donor atoms such as As or Sb. Given nᵢ=1.5×10¹⁶ m⁻³, find electron and hole concentrations. Assume fully ionised donors, no compensation and thermal equilibrium.

Check answer
N_D=10⁻⁶(5×10²⁸)=5×10²² m⁻³; n≈N_D and p=nᵢ²/n=4.5×10⁹ m⁻³. It is n-type.
Q0192026 · 2025–26 · 2025 · 2024–25 · 2024 · 2023–24 · 2023 · 2022 · 2021–22 · 2020 · 2019 · 2018 · 2016 · 2015 · 2012 · 2011 · 2010 · 2007Board · Sample paperRectifiers and filters

Draw and explain a two-diode centre-tapped full-wave rectifier, including input and output waveforms. Compare it with half-wave rectification. State the role and connection of a smoothing capacitor. Give the full-wave ripple frequency for a 60 Hz input as well.

Check answer and diagram
The secondary ends have opposite instantaneous polarity relative to the centre tap. D₁ and D₂ conduct on alternate half-cycles but send current through R_L in the same direction. For equal secondary halves and ideal diodes v_out=|Vₘ sinωt|; ripple frequency is 2f, versus f for half-wave rectification. Without filtering the output is pulsating DC. A capacitor is connected in parallel with R_L: it charges near peaks and supplies the load between peaks, reducing ripple; smoothing depends on load and RC, and is not automatically perfect DC. For a 60 Hz input, equal-pulse full-wave ripple is 120 Hz.
Q0212026BoardAdapted questionRectifiers and filters

A half-wave rectifier has ideal maximum rectification efficiency near 40.6%. Does that mean roughly 59.4% of the input power must be dissipated inside the diode? Explain.

Check answer
No. Rectification efficiency is DC-component load power divided by total AC input power. Even an ideal lossless diode gives η=4/π²≈40.6% for a sinusoid and resistive load: the remaining load-power contribution is associated with the AC ripple component. Real diodes and transformers can introduce additional heating losses.
Q0242026BoardAdapted questionSemiconductors and temperature

(a) Why is manganin useful in standard wire-wound resistors? A separate wire has α=0.004 °C⁻¹ and resistance measured at 27.5 °C. In the linear model find the temperature for a 25% increase. (b) Sketch resistivity versus temperature for an intrinsic semiconductor.

Check answer and diagram
Manganin has low temperature coefficient and useful resistivity. For the separately specified wire, 1+α(T−27.5)=1.25, so T=90.0 °C. The given α is not a realistic manganin coefficient and should not be assigned to the manganin resistor. Intrinsic-semiconductor resistivity generally decreases as thermal carrier generation increases. The curve below is that sketch: ρ is high at low temperature and falls as T rises.
Q0252026BoardAdapted questionp–n junction and diode bias

Estimate the average electric-field magnitude in a depletion region 2.0 μm wide with a potential drop of 0.4 V. Treat the field as uniform for this estimate.

Check answer
E_avg=ΔV/d=0.4/(2.0×10⁻⁶)=2.0×10⁵ V/m. In an actual junction the field varies with position; this is its mean magnitude.
Q0272026 · 2025 · 2024–25 · 2024 · 2023 · 2022 · 2020 · 2019 · 2016 · 2015 · 2012 · 2009Board · Sample paperp–n junction and diode bias

Explain diffusion, drift, depletion-layer formation and barrier potential in an initially unbiased p–n junction. Describe how the two opposing currents evolve towards thermal equilibrium. Include a labelled junction diagram.

Check answer and diagram
Electrons diffuse n→p and holes p→n, leaving fixed positive donors on the n side and negative acceptors on the p side. This space-charge region is depleted of mobile majority carriers. Its field points n→p and opposes further majority diffusion, while driving minority-carrier drift. As the barrier develops, net diffusion decreases and opposing drift develops; at equilibrium their magnitudes are equal and net current is zero. Dopant ions remain fixed in the lattice.
Q0282026BoardAdapted questionp–n junction and diode bias

Assertion: forward bias increases the junction barrier height. Reason: the applied electric field in forward bias reinforces the built-in depletion field. Evaluate both statements.

Check answer
Both false. Forward bias opposes the built-in field, reducing the barrier and narrowing the depletion region.
Q0312026Board1 markp–n junction and diode bias

Which of the four diode arrangements shown is forward biased? Compare anode and cathode potentials, including their signs.

Check answer
B: the anode is at −1.0 V and cathode at −1.5 V, so V_A−V_K=+0.5 V. Forward bias depends on the potential difference, not whether both terminals are positive or negative relative to ground.
Q0322026BoardAdapted questionp–n junction and diode bias

In the supplied potential-profile sketch, curve 2 represents the unbiased junction. Identify forward and reverse bias for curves 1 and 3.

Check answer
Curve 3 is forward bias (lower barrier); curve 1 is reverse bias (higher barrier). Thus option B is correct. The horizontal coordinate is position across the junction, not an externally swept voltage.
Q0352025Board3 marksDiode bias and I–V characteristics

(a) Identify majority/minority carriers in p-type and n-type material. (b) Describe forward-bias carrier motion. (c) Estimate dynamic resistance at V=−0.6 V from the supplied I–V curve.

Check answer
(a) p-type: holes/electrons; n-type: electrons/holes. (b) Electrons cross n→p and holes p→n. (c) This point is on the nearly horizontal reverse-saturation branch: dI/dV≈0, so r_d=dV/dI is extremely large (infinite in the ideal flat-branch approximation). V/I is static resistance and is not the requested dynamic resistance. The unscaled reverse-current axis cannot give a finite numerical slope.
Q0362025Board2 marksDiode bias and I–V characteristics

Diode voltage rises from 0.90 V to 0.95 V and current increases by 0.005 A. Find average dynamic resistance.

Check answer
r=ΔV/ΔI=0.05/0.005=10 Ω.
Q0382025BoardAdapted questionDiode circuits and numerical problems

A reverse-biased p–n junction has conducting regions separated by an insulating depletion layer. Which circuit element does this structure resemble, and why can a resistance meter simultaneously show high resistance?

Check answer
It has junction capacitance: the p and n regions act as plates separated by the depletion region. High DC resistance describes its small reverse leakage; it does not exclude capacitive response to changing voltage. A reverse-biased diode may also serve as an open switch, so high resistance alone does not uniquely identify a capacitor.
Q0392025Board2 marksDiode circuits and numerical problems

A silicon diode is modelled with a constant 0.7 V forward drop and is in series with a 1000 Ω resistor. Find the battery voltage for 15 mA.

Check answer
V=V_D+IR=0.7+0.015×1000=15.7 V. “At the threshold” here means the constant-drop approximation, not exactly zero current.
Q0402025Board3 marksEnergy bands

Distinguish n-type and p-type semiconductors. Why is electron mobility typically greater than hole mobility in silicon or germanium?

Check answer
n-type: donor impurities and majority electrons; p-type: acceptors and majority holes. Mobility depends on band structure, effective mass and scattering. Conduction electrons typically have higher mobility than valence-band holes in Si/Ge; it is not because holes are literal heavy particles or because one carrier has a larger elementary charge.
Q0422025BoardAdapted questionEnergy bands

Band and junction case: (i) State the carrier relation in an intrinsic semiconductor and the trend of its resistance with temperature. (ii) Identify an n-type dopant for Ge. (iii) Give Ge’s approximate band gap at 0 K. (iv) State the change in depletion width and barrier height under reverse bias. Also state net current in an unbiased equilibrium junction.

Check answer
(i) n=p=nᵢ; intrinsic resistance generally decreases with temperature. (ii) A pentavalent dopant such as phosphorus. (iii) About 0.74 eV at 0 K; about 0.66–0.67 eV at room temperature. (iv) Both barrier height and depletion width increase. At equilibrium diffusion and drift currents cancel; net current is zero.
Q0432026–27 · 2025 · 2023 · 2022 · 2020 · 2016 · 2015 · 2014 · 2010 · 2007Board · Sample paperAdapted questionEnergy bands

Draw band diagrams of a conductor, intrinsic semiconductor and insulator at 0 K. Explain electron–hole generation at room temperature. Why is diamond insulating while Si is semiconducting and ordinary white tin metallic, despite all being group-IV elements?

Check answer and diagram
A metal has a partially occupied band or overlapping bands. At 0 K an intrinsic semiconductor and an insulator have full valence bands and empty conduction bands, but the semiconductor has a much smaller gap. Thermal excitation across the gap produces equal electron and hole densities. Diamond has a gap about 5.4–5.5 eV; Si about 1.1 eV at room temperature, so far more carriers are thermally available in Si. Ordinary white β-Sn has metallic bands. Carbon’s behaviour depends on allotrope (graphite conducts), and grey α-Sn differs from white tin; group number alone does not determine conductivity.
Q0442025Board1 markEnergy bands

Assertion: a hole behaves as a mobile carrier of effective charge +e. Reason: a hole need not be a vacancy of an electron in an otherwise occupied valence-band state. Evaluate in the elementary semiconductor model.

Check answer
Assertion true; reason false. A valence-band vacancy is described as a hole of positive effective charge; neighbouring electron motion makes the vacancy move.
Q0452025 · 2024 · 2023 · 2022 · 2021–22 · 2020–21 · 2020 · 2019–20 · 2019 · 2015 · 2007Board · Sample paperAdapted questionEnergy bands

Draw n-type and p-type energy-band diagrams for T>0 K. Show donor/acceptor levels and explain their roles. Compare ordinary nondegenerately doped semiconductors at 0 K and room temperature.

Check answer and diagram
Donor levels lie just below E_C; acceptor levels just above E_V. Small thermal energies ionise donors to put electrons in the conduction band or populate acceptors from the valence band, leaving holes. The ionisation energy is much smaller than the host band gap (order 10⁻² eV; Si donors often about 0.05 eV, Ge donors about 0.01 eV). In the elementary isolated-impurity model, carriers freeze out at 0 K; at room temperature doped carriers conduct. This does not describe degenerate, very heavily doped material.
Q0472025Board2 marksIntrinsic and extrinsic semiconductors

A p-type Si sample has p=2.25×10¹⁵ cm⁻³ and nᵢ=1.5×10¹⁰ cm⁻³. Calculate n in equilibrium at the same temperature.

Check answer
n=nᵢ²/p=1.0×10⁵ cm⁻³=1.0×10¹¹ m⁻³. Do not mix cm⁻³ and m⁻³ inside the calculation.
Q0482025Board1 markIntrinsic and extrinsic semiconductors

Assertion: simply pressing separate p-type and n-type slabs together does not produce the usual p–n junction. Reason: holes dominate in p-type and electrons in n-type. Evaluate the explanatory link; give the actual reason.

Check answer
Both statements are true, but the reason does not explain the assertion. A useful junction is formed within a continuous crystal; a rough physical interface introduces gaps, defects and surface states rather than the intended continuous junction.
Q0492025Board2 marksIntrinsic and extrinsic semiconductors

Silicon has 5×10²⁸ atoms m⁻³ and is p-doped with one acceptor per 5×10⁷ Si atoms. Estimate the added holes per cm³, assuming full ionisation and negligible compensation, and name a dopant.

Check answer
N_A=10²¹ m⁻³=10¹⁵ cm⁻³. A dopant such as boron, aluminium or indium can supply acceptor sites.
Q0512025Board2 marksIntrinsic and extrinsic semiconductors

An intrinsic semiconductor has nᵢ=5×10⁸ m⁻³. After doping at the same temperature its hole density is 8×10¹² m⁻³. Identify dopant/type and calculate n. Assume equilibrium.

Check answer
A trivalent acceptor gives p-type material. n=nᵢ²/p=3.125×10⁴ m⁻³.
Q0532025BoardAdapted questionIntrinsic and extrinsic semiconductors

Assertion: acceptors in ordinary p-type silicon are not pentavalent donor atoms. Reason: for fully ionised, uncompensated acceptors with p≫nᵢ, hole density is approximately the acceptor density. Evaluate the explanatory link.

Check answer
Both are true under the stated conditions; the concentration relation alone does not explain the valence classification. Trivalent acceptors take a valence electron, leaving a hole. Whether the reason is considered an explanation depends on what mechanism it states; here it states only a density relation, so it is not a complete explanation.
Q0542025Board2 marksIntrinsic and extrinsic semiconductors

In an n-type semiconductor, electron–hole recombination continues at room temperature. Why does n remain greater than p?

Check answer
Thermal generation and recombination balance in equilibrium. Ionised donors supply excess electrons; charge neutrality and np=nᵢ² give n≈N_D≫p in the usual extrinsic regime. Recombination does not permanently exhaust the equilibrium carrier population.
Q0582025BoardAdapted questionRectifiers and filters

Junction case: name a donor for Ge; give an approximate donor binding energy for Si; identify the signs of fixed depletion charges; explain where reverse voltage mainly drops; find full-wave ripple frequency for a 50 Hz input.

Check answer
Sb is a Ge donor. Si donor-ionisation energies are typically about 0.05 eV (Ge about 0.01 eV); a single 0.01 eV value should not be assigned universally to Si. Positive donors remain on the n side, negative acceptors on the p side. Most reverse voltage drops across the high-resistance depletion layer. Full-wave ripple frequency is 100 Hz.
Q0612025 · 2023 · 2021–22 · 2019 · 2015–16 · 2015 · 2012 · 2011 · 2007Board · Sample paperAdapted questionSemiconductors and temperature

Define resistivity. Sketch typical ρ(T) for a normal metal and an intrinsic semiconductor, and explain the difference using carrier density and relaxation time. Give one example of each temperature-coefficient sign.

Check answer and diagram
ρ=RA/L; for one carrier species ρ=m*/(ne²τ). In a normal metal n changes little while lattice scattering reduces τ as T rises, so ρ increases (e.g. copper). In an intrinsic semiconductor thermally generated electrons and holes increase strongly, usually dominating mobility reduction, so ρ decreases (e.g. intrinsic Ge). In general σ=e(nμₑ+pμₕ). These trends refer to the stated regimes; heavily doped semiconductors need not have the same sign at every temperature.
Q0642025Board1 markp–n junction and diode bias

Assertion: depletion-layer thickness is not fixed. Reason: it depends on bias and doping. Evaluate and describe both dependencies.

Check answer
Both true, and the reason explains the assertion. Forward bias narrows the layer; reverse bias widens it. Higher doping generally makes it narrower for the same material, temperature and applied bias, with the layer extending farther into the more lightly doped side.
Q0662025BoardAdapted questionp–n junction and diode bias

In which forward-bias region is an ordinary diode used when substantial conduction is required: below or beyond its approximate knee voltage?

Check answer
Beyond the approximate knee. This describes forward conduction, not every use of a diode: it may also be reverse biased, switched off, or used through its junction capacitance.
Q0682024 · 2023BoardEnergy bands

Explain how valence and conduction energy bands form in a crystalline solid, and define the band gap.

Check answer and diagram
Overlap and interaction of many atoms split their discrete levels into closely spaced allowed levels: energy bands. The valence band derives from valence states; the conduction band is the next relevant higher allowed band. The forbidden gap separates the valence-band maximum E_V from conduction-band minimum E_C: E_g=E_C−E_V. No allowed extended band states lie in an ideal gap, although impurities can introduce localised levels.
Q0712024Board1 markEnergy bands

Assertion: conduction-band electrons have less energy than valence-band electrons in a semiconductor. Reason: donor levels lie just above the valence band. Evaluate both statements.

Check answer
Both false. The conduction-band minimum is above the valence-band maximum; donor levels lie just below the conduction band. Acceptor levels lie just above the valence band.
Q0762024BoardAdapted questionIntrinsic and extrinsic semiconductors

In one continuous silicon crystal, region A is As-doped and region B is B-doped. Use the supplied battery polarity to identify the bias and sketch the relevant I–V branch.

Check answer and diagram
A is n-type and is connected to the positive battery terminal; B is p-type and is connected to the negative terminal. The junction is reverse biased: current is small and nearly constant below breakdown. Plot the reverse branch in the negative-V, negative-I quadrant, with a separate small-current scale if necessary.
Q0782024Board2 marksIntrinsic and extrinsic semiconductors

Sketch conductivity versus temperature for an intrinsic semiconductor and explain the trend.

Check answer and diagram
Conductivity generally increases steeply with temperature because electron–hole generation increases nᵢ; σ=e nᵢ(μₑ+μₕ). Mobility can decrease, but carrier generation dominates in the usual intrinsic regime. At 0 K the ideal intrinsic material has no free carriers.
Q0802024BoardAdapted questionIntrinsic and extrinsic semiconductors

Does weak trivalent or pentavalent doping simply shrink the intrinsic semiconductor’s full band gap to the dopant-ionisation energy? Explain with levels.

Check answer
No. In the elementary weak-doping model the host E_C−E_V remains approximately unchanged. Acceptors introduce levels slightly above E_V; donors introduce levels slightly below E_C. The small energy needed to activate these carriers is not the full host band gap. Heavy doping can modify bands and lies outside this approximation.
Q0812024Board1 markIntrinsic and extrinsic semiconductors

Give the approximate energy needed to free a weakly bound donor electron in silicon, and compare it with the full band gap.

Check answer
Typically about 0.05 eV for common shallow Si donors, much less than the room-temperature gap of about 1.1 eV. For Ge common donors are nearer 0.01 eV; the two materials should not be confused.
Q0822024Board2 marksIntrinsic and extrinsic semiconductors

Pure Si has 5×10²⁸ atoms m⁻³ and is doped with 1 ppm of B. Given nᵢ=1.5×10¹⁶ m⁻³, find p and n. Assume full ionisation, no compensation and equilibrium.

Check answer
N_A=5×10²² m⁻³. The p-type sample has p≈5×10²² m⁻³ and n=nᵢ²/p=4.5×10⁹ m⁻³.
Q0832024Board1 markIntrinsic and extrinsic semiconductors

Pure Si has 5×10²⁸ atoms m⁻³ and 1 ppm of Sb. If p=4.5×10⁹ m⁻³, estimate nᵢ at this temperature. Assume full donor ionisation and equilibrium.

Check answer
n≈5×10²² m⁻³; nᵢ=√(np)=√(2.25×10³²)=1.5×10¹⁶ m⁻³.
Q0842026 · 2024BoardIntrinsic and extrinsic semiconductors

Explain why a doped semiconductor can be neutral, why an unbiased equilibrium junction has zero net current, and why reverse current is almost independent of voltage below breakdown.

Check answer
Ionised dopants balance excess mobile carriers. At equilibrium opposite diffusion and drift currents balance. Below breakdown most thermally generated minority carriers reaching the depletion region are already swept across, so their generation/supply rate chiefly sets reverse saturation current; it depends strongly on temperature. Most applied reverse voltage drops across the high-resistance depletion region.
Q0852024Board2 marksIntrinsic and extrinsic semiconductors

What considerations guide the choice of dopants for Si or Ge?

Check answer
Choose donor or acceptor valence to obtain the required carriers; suitable atomic size and compatibility allow substitution into the host lattice without excessive defects. Control concentration and purity, use shallow levels that ionise at the operating temperature, and avoid unwanted compensation. Doping is small and controlled, not arbitrary contamination.
Q0872024Board1 markRectifiers and filters

Describe the output of an ideal unfiltered full-wave rectifier with sinusoidal input. Is it steady DC?

Check answer
It is unidirectional pulsating voltage |Vₘ sinωt| with ripple, reaching zero at each input zero crossing. It is not a constant DC voltage. For a resistive load the ripple repeats at twice the input frequency.
Q0882024BoardAdapted questionRectifiers and filters

Use the supplied circuits with ideal diodes. (i) Which bulb glows? (ii) Which labelled output pulses come from D₁, assuming it conducts on the first positive half-cycle? OR describe an unfiltered half-wave output. (iii) Name the majority carriers on p and n sides. (iv) For the same 50 Hz input, find full-wave ripple frequency.

Check answer
(i) Only B₁ glows: D₁ is forward biased and D₂ reverse biased. (ii)(a) D₁ supplies alternate pulses A and C; (b) the half-wave output is unidirectional with ripple. (iii) Majority carriers are holes on p side and electrons on n side. (iv) For the same 50 Hz supply, full-wave ripple is 100 Hz.
Q0892024 · 2019BoardAdapted questionRectifiers and filters

For an ideal unfiltered two-diode full-wave rectifier with equal secondary halves and resistive load: (i) if either half-secondary has RMS Vₘ/√2, find output RMS; (ii) how long does each diode conduct per cycle? (iii) Describe their relative bias. (iv) Find half-wave ripple frequency for 50 Hz. OR sketch the load output when the supplied +5/−5 V square wave drives the series diode and R_L.

Check answer and diagram
(i) Full-wave rectification preserves the RMS of that half-secondary sinusoid: Vₘ/√2. Its DC mean is 2Vₘ/π, a different quantity. (ii) Each diode conducts for half a cycle. (iii) Except at zero crossings, one is forward and the other reverse biased. (iv)(a) Half-wave ripple is 50 Hz; (b) the +5/−5 V input becomes +5/0 V pulses across R_L, option D.
Q0902024Board4 marksRectifiers and filters

Junction case: (i) Give the donor binding-energy order in Ge. (ii) nᵢ=2×10¹⁰ cm⁻³ and doped p=8×10³ cm⁻³: find n in m⁻³. (iii) Describe initial diffusion directions and initial diffusion/drift magnitudes. (iv) Find half-wave and full-wave ripple frequencies for v=0.5 sin(100πt) V.

Check answer
(i) About 0.01 eV. (ii) n=nᵢ²/p=5×10¹⁶ cm⁻³=5×10²² m⁻³; use consistent units. (iii) Electrons diffuse n→p and holes p→n; initially diffusion dominates before the space-charge field builds up. (iv) ω=100π gives f=50 Hz; half-wave ripple 50 Hz and full-wave ripple 100 Hz.
Q0922024BoardAdapted questionSemiconductors and temperature

Assertion: normal metals have positive temperature coefficient of resistivity, while a p-type semiconductor in its thermally activated regime has a negative coefficient. Reason: metals conduct through negative electrons whereas p-type material has positive majority holes. Evaluate the causal link.

Check answer
Both are true in the stated regimes, but carrier charge sign does not explain the temperature coefficient. Metal scattering increases with T; thermal carrier generation can dominate in the semiconductor. Doped semiconductor behaviour outside this regime can differ.
Q0942024Board1 markp–n junction and diode bias

Which claim is false for a reverse-biased junction below breakdown: current is nearly voltage independent; majority holes flow p→n; depletion field strengthens; n is connected to positive and p to negative?

Check answer
“Majority holes flow p→n” is false in this reverse-current description. Reverse current is mainly minority-carrier drift: minority holes are swept n→p and minority electrons p→n.
Q0972026 · 2025 · 2024 · 2023 · 2022 · 2020 · 2019 · 2015 · 2011Boardp–n junction and diode bias

Explain how forward and reverse bias affect barrier height, depletion width and junction resistance. Include battery polarities.

Check answer
Forward: p positive, n negative; barrier and width decrease, allowing substantial majority diffusion and relatively low resistance. Reverse: p negative, n positive; barrier and width increase, giving high resistance and small minority-carrier current below breakdown. In forward bias electrons cross n→p and holes p→n.
Q0992023BoardAdapted questionDiode bias and I–V characteristics

(a)(i) Draw a forward-bias I–V measurement circuit, mark the approximate knee and explain it. (ii) Find V_A−V_B in the shown series circuit: two 5 kΩ resistors, forward diode drop 0.3 V and downward current 0.2 mA. OR (b)(i) Classify metal, semiconductor and insulator by bands. (ii) For current rising 10→20 mA as voltage rises 0.6→0.7 V, find average dynamic resistance.

Check answer and diagram
(a)(i) Use the forward-bias measurement circuit; the knee is an approximate onset of rapid current increase, not a perfectly abrupt physical threshold. (ii) V_A−V_B=IR₁+0.3+IR₂=1+0.3+1=2.3 V. (b)(i) Metal: partly filled/overlapping bands; semiconductor: small gap; insulator: large gap. (ii) r=(0.7−0.6)/(0.020−0.010)=10 Ω.
Q1002023Board1 markDiode circuits and numerical problems

For a sinusoidal AC source, one series ideal diode and a resistive load, select the output waveform from the supplied options. Assume the diode passes the positive half-cycle.

Check answer
C: positive half-sine pulses separated by zero output on negative half-cycles. One diode gives half-wave rectification, not the full-wave waveform B or perfectly constant output D.
Q1022023BoardAdapted questionDiode circuits and numerical problems

For the pictured 0.5 V battery, 100 Ω resistor and forward-oriented diode, use a constant-drop model with V_on=0.7 V and no reverse leakage. State bias and current.

Check answer
Forward bias, but the supply is below the model’s turn-on voltage, so I=0 A in this simplified model (option A). Real diode current is gradual and need not be exactly zero at 0.5 V.
Q1062023Board1 markEnergy bands

Approximately how much energy is needed to excite an electron from the valence band to the conduction band of Si at room temperature?

Check answer
About 1.1 eV, the full band gap; 0.01–0.05 eV describes shallow impurity activation, not crossing the full gap.
Q1072023BoardIntrinsic and extrinsic semiconductors

Assertion: silicon is generally preferred over germanium for ordinary semiconductor devices. Reason: Ge has a larger band gap than Si. Evaluate and explain the usual temperature advantage. Also assess the alternative reason: “Si can generally operate at higher temperatures than Ge in this comparison.”

Check answer
Assertion generally true in this textbook comparison; reason false. Si has the larger gap (about 1.1 eV versus Ge’s 0.66–0.67 eV at room temperature), giving lower intrinsic leakage and useful operation at higher temperatures. Material choice also depends on the device application. The alternative reason is true and explains the usual preference for Si under the stated thermal comparison.
Q1122023Board1 markIntrinsic and extrinsic semiconductors

A semiconductor has p=4×10²⁰ m⁻³ and nᵢ=1.2×10¹⁵ m⁻³. Find electron density at thermal equilibrium.

Check answer
n=nᵢ²/p=(1.44×10³⁰)/(4×10²⁰)=3.6×10⁹ m⁻³.
Q1142023Board2 marksIntrinsic and extrinsic semiconductors

Explain why excessive current can damage a junction diode and why controlled impurities are deliberately added to intrinsic semiconductors.

Check answer
Excessive current causes Joule heating and can damage the junction or contacts, so current must be limited. Controlled doping sets carrier concentration and conductivity for useful device operation; it does not mean arbitrary impurities improve a device.
Q1152023Board1 markIntrinsic and extrinsic semiconductors

A two-terminal device in series with a battery, resistor and ammeter carries current in one polarity but almost none when the battery is reversed. Identify the device.

Check answer
An ordinary p–n junction diode, operated below reverse breakdown. A bare uniformly doped n-type or p-type resistor alone does not provide this junction rectification.
Q1162023Board1 markIntrinsic and extrinsic semiconductors

At fixed temperature nᵢ=1.5×10¹⁶ m⁻³. Trivalent doping gives p=4.5×10²² m⁻³. Find n at equilibrium.

Check answer
n=nᵢ²/p=5×10⁹ m⁻³.
Q1172023Board1 markIntrinsic and extrinsic semiconductors

What is the resistivity of an ideal intrinsic semiconductor at 0 K in the elementary band model?

Check answer
Infinite: its full valence band and empty conduction band provide no free carriers. This idealisation excludes impurities, defects and tunnelling.
Q1182023BoardAdapted questionIntrinsic and extrinsic semiconductors

State the relations between n, p and nᵢ in an intrinsic semiconductor at thermal equilibrium, and distinguish them from the general mass-action law.

Check answer
Intrinsic: n=p=nᵢ. Therefore nᵢ=√(np) also holds. For nondegenerate extrinsic material in equilibrium np=nᵢ², while generally n≠p. The two intrinsic identities are simultaneously true, so they cannot be offered as mutually exclusive single-answer options.
Q1212023BoardRectifiers and filters

Which supplied capacitor connection correctly smooths a half-wave rectifier’s output? Explain how it works.

Check answer
C: connect the capacitor in parallel with the load resistor after the diode. It charges near voltage peaks and discharges through the load between them. A series capacitor or one connected across the AC source does not perform this output smoothing.
Q1272023BoardAdapted questionSemiconductors and temperature

Assertion: resistivity increases with temperature for a normal metal and decreases for an intrinsic semiconductor. Reason: metal carriers are negative, whereas semiconductor carriers are always positive. Evaluate both statements.

Check answer
Assertion true in the usual stated regime; reason false. Both electrons and holes conduct in an intrinsic semiconductor. The different temperature dependence comes from scattering and carrier generation, not charge sign.
Q1372023Board1 markp–n junction and diode bias

Assertion: an n-type crystal has more conduction electrons than holes yet remains electrically neutral. Reason: donor electrons are balanced by oppositely charged ionised donors. Evaluate.

Check answer
Both true, and the reason explains neutrality. Charge neutrality accounts for fixed impurity ions as well as mobile carriers.
Q1392023BoardAdapted questionp–n junction and diode bias

Assertion: an ordinary band insulator has a large forbidden gap. Reason: its valence electrons are tightly bound and not easily excited into mobile conduction states. Evaluate at the elementary band-theory level.

Check answer
Both true, and the reason describes why a large excitation energy is needed. A full valence band alone does not conduct as a partly occupied band does; few thermal carriers cross a large gap at room temperature.
Q1442022Board2 marksEnergy bands

(a) Explain why diamond is insulating while Si is semiconducting despite related crystal structures. (b) What is observed if one slit of a Young double-slit arrangement is closed?

Check answer
(a) Diamond has a much wider gap (about 5.4–5.5 eV versus Si’s roughly 1.1 eV at room temperature), so thermal excitation supplies far fewer carriers. (b) Two-slit interference fringes disappear. A finite-width remaining slit can still give a single-slit diffraction envelope; the screen is not necessarily perfectly uniform.
Q1492022 · 2020BoardAdapted questionIntrinsic and extrinsic semiconductors

Explain how a p–n junction is formed. Can it be made by merely pressing two separate doped slabs into physical contact?

Check answer
A controlled doping profile creates adjacent p and n regions within a continuous crystal. Majority-carrier diffusion establishes fixed depletion charge and a built-in field; at equilibrium drift and diffusion balance. Simply pressing slabs together gives an uncontrolled, defective interface rather than the intended crystal junction.
Q1502022Board2 marksIntrinsic and extrinsic semiconductors

(a) Explain neutrality of a p-type semiconductor despite holes being the majority carriers. (b) In the photon picture, what determines monochromatic light intensity?

Check answer
(a) Negative ionised acceptors balance the excess positive mobile holes. (b) Intensity is energy flux: I=(photon number per unit area per unit time)hν. At fixed frequency it is proportional to photon flux.
Q1512022Board2 marksIntrinsic and extrinsic semiconductors

(a) Explain neutrality of an n-type semiconductor despite electrons being majority carriers. (b) State the condition for two monochromatic sources to be mutually coherent.

Check answer
(a) Positive ionised donors balance excess mobile electrons. (b) They must have the same frequency and a stable phase difference over the observation interval; appropriate polarisation is also needed to observe interference.
Q1592022 · 2014 · 2009BoardRectifiers and filters

Draw and explain a single-diode half-wave rectifier, with input and output waveforms for an ideal diode and resistive load.

Check answer and diagram
The diode conducts on the positive input half-cycle and blocks the negative half-cycle for the shown orientation. Current through R_L is unidirectional but pulsating; ripple frequency equals the input frequency. With no capacitor v_out=max(0,V_m sinωt).
Q1792020–21 · 2020Board · Sample paperp–n junction and diode bias

How does increased doping affect depletion width at fixed material, temperature and applied bias?

Check answer
Higher doping generally narrows the depletion layer because a shorter region supplies the fixed charge needed for the junction field. In an abrupt junction W²∝(1/N_A+1/N_D)(V_bi−V_forward), or V_bi+V_reverse. The built-in potential also depends on doping, but the usual narrowing trend remains in the elementary model.
Q1972019Board3 marksSemiconductors and temperature

Derive current I in terms of charge-carrier number density n, cross-sectional area A and drift-speed magnitude v_d. How does intrinsic semiconductor resistivity generally vary with temperature?

Check answer
In Δt, nAv_dΔt carriers cross a section; I=neAv_d for one species of charge magnitude e. Electrons drift opposite conventional current. Intrinsic semiconductor resistivity generally falls as thermal generation raises electron and hole densities.
Q2032017Board3 marksRectifiers and filters

In the supplied grounded-anode circuit with the cathode connected through a resistor to +5 V, identify the bias. Then draw and explain a two-diode full-wave rectifier.

Check answer and diagram
The anode is at 0 V and cathode near +5 V, so it is reverse biased. In a centre-tapped rectifier the secondary ends drive two diodes on alternate half-cycles; their joined cathodes supply positive load current, returning through the centre tap, giving full-wave pulsating output.
Q2322007BoardAdapted questionDiode bias and I–V characteristics

In a continuous Ge crystal, X is In-doped and Y is As-doped. X is connected to the negative battery terminal and Y to positive. Identify the bias and sketch its I–V branch.

Check answer and diagram
X is p-type, Y n-type: the junction is reverse biased. The reverse branch has a small negative saturation current below breakdown. Adjacent doped regions must be in one continuous crystal; physical slab contact alone is not a usual p–n junction.
Q2332007Board1 markDiode bias and I–V characteristics

Two diodes point from left (anode) to right (cathode). D₁ has anode at −2 V and cathode connected through a resistor to ground. D₂ has anode grounded and cathode connected through a resistor to −2 V. Identify their bias.

Check answer
D₁ is reverse biased (anode lower than cathode). D₂ is forward biased (anode higher than cathode). Ground is 0 V; negative potentials must still be compared algebraically.
Q2392026–27Sample paperAdapted questionIntrinsic and extrinsic semiconductors

A proposed flexible electronic sensor uses an organic semiconductor. (i) Why can low-power, reliable electronics be useful in wearable devices? (ii) Compare thermal excitation across diamond’s 5.4 eV gap and Si’s 1.1 eV gap. (iii) State the intrinsic carrier relation. (iv) Can majority/minority-carrier labels alone establish a polymer device’s efficiency?

Check answer
(i) Low power extends battery life and reliability supports sustained monitoring. (ii) Si’s smaller gap permits far more thermal excitation at room temperature; ordinary undoped diamond has very few carriers. (iii) n=p=nᵢ at equilibrium. (iv) No: mobility, carrier density, trapping, contacts, architecture and power losses must be known. Flexibility, biodegradability and device efficiency are material-specific, not universal semiconductor properties.
Q2402025–26Sample paperAdapted questionDiode circuits and numerical problems

Use the four shown circuits. (i) How much does V₀ change when Ge is reversed? Use drops Ge=0.3 V and Si=0.7 V. (ii) Find V₀ and diode current with the same constant drops. (iii) Find current through 100 Ω: each diode has zero threshold, 50 Ω forward resistance and infinite reverse resistance. (iv) Find V_AB for an ideal diode.

Check answer
(i) Initially Ge sets a 0.3 V drop, so V₀=11.7 V. Reversing Ge leaves Si conducting: V₀=11.3 V, a decrease of 0.4 V. (ii) V₀=12−0.7−0.3=11 V and I=11/5600≈1.964 mA. (iii) D₁ conducts and D₂ is blocked: I=6/(50+150+100)=0.020 A through 100 Ω. (iv) The two lower 10 kΩ branches are parallel; V_AB=30(5)/(10+5)=10 V.
Q2422024–25Sample paperAdapted questionIntrinsic and extrinsic semiconductors

In the ordinary extrinsic temperature range with donors already essentially ionised, what chiefly sets the electron concentration donated by dopants? Does this remain true at donor freeze-out or very high temperature?

Check answer
The donor concentration chiefly sets n≈N_D in the stated regime, so it depends strongly on doping level. At very low temperature ionisation depends on temperature; at sufficiently high temperature intrinsic carrier generation becomes important. A temperature-independent rule is not valid in every regime.
Q2432024–25Sample paperAdapted questionIntrinsic and extrinsic semiconductors

(i) Sketch p-type bands at 0 K and room temperature in the nondegenerate impurity model. (ii) A bulb is connected across a cell with finite internal resistance; a parallel branch contains a switch and ideal forward-oriented diode. Does it glow with the switch open or closed?

Check answer and diagram
(i) At 0 K acceptor states are empty and the valence band full in the isolated-impurity model. At room temperature acceptors capture valence electrons, leaving mobile holes; E_A lies just above E_V. (ii) Open switch: current flows through the bulb and it glows. Closed switch: the forward diode shunts the bulb, making its voltage approximately zero, so it goes off. Finite internal/series resistance is essential to limit the short-circuit current.
Q2442024–25Sample paperAdapted questionRectifiers and filters

(i) In the supplied AC→X→Y→DC-load diagram identify the usual rectification and smoothing stages, and sketch their outputs. (ii) If a two-diode rectifier’s tap is shifted towards D₁, describe the output for an unfiltered resistive load.

Check answer and diagram
(i) X is a rectifier producing pulsating DC; Y is a filter reducing ripple. (ii) D₁ has fewer secondary turns and produces smaller pulses; D₂ has more turns and produces larger alternating pulses of the same polarity. They have unequal peaks, not alternating polarity. The unequal pulse train repeats at the input period, so it contains a component at f as well as higher ripple harmonics; it is no longer the equal-peak |sin| waveform.
Q2472023–24Sample paperAdapted questionDiode circuits and numerical problems

Use the supplied figures. (i) Find current for 3.5 V, 100 Ω and forward diode drop 0.5 V. (ii) Which of the four voltage arrangements reverse biases the diode? (iii) Describe why its I–V relation is non-ohmic. OR in which series arrangements do identical junctions share the same voltage in the symmetric model? (iv) Compare DC resistances |V/I| at I≈15 mA and at V=−10 V; separately estimate forward dynamic resistance from the marked 10–20 mA points.

Check answer
(i) I=(3.5−0.5)/100=30 mA. (ii) C is reverse biased: grounded anode and cathode connected to +5 V. (iii) The diode is non-ohmic; it is also passive, so those categories are not exclusive. OR: arrangements 2 and 3 put identical junctions in the same bias sense and give equal sharing in the ideal symmetric model. (iv) V_F≈0.75 V gives R_DC,F≈50 Ω; |I_R|≈1 μA gives R_DC,R≈10 MΩ, so the DC ratio is approximately 5×10⁻⁶. The forward slope gives r_d≈(0.8−0.7)/(0.020−0.010)=10 Ω. Comparing that dynamic value with reverse DC resistance would instead give 10⁻⁶; these are different definitions.
Q2492023–24Sample paper1 markp–n junction and diode bias

Assertion: simply contacting separate p-type and n-type slabs does not form the usual p–n junction. Reason: a rough interface has gaps and defects on scales larger than crystal spacing, preventing the intended continuous crystal junction. Evaluate.

Check answer
Both true, and the reason explains the assertion in this elementary construction argument. A controlled junction is formed inside a continuous semiconductor crystal.
Q2512022–23Sample paperAdapted questionIntrinsic and extrinsic semiconductors

Assertion: ordinary controlled doping increases semiconductor conductivity in its extrinsic operating regime. Reason: doping always increases electron density. Evaluate.

Check answer
Assertion true in the stated regime; reason false. Acceptor doping increases hole density and can decrease minority-electron density. σ=e(nμₑ+pμₕ), so either carrier type can raise conductivity.
Q2522022–23Sample paper2 marksSemiconductors and temperature

A pure semiconductor S, variable resistor R and ammeter are in series with a constant-voltage source. When S is heated in its intrinsic operating regime, how should R change to keep current fixed?

Check answer
Increase R. Heating lowers the intrinsic semiconductor’s resistance, so R must increase by the same amount to keep total resistance V/I constant, provided the adjustment range is sufficient.
Q2532022–23Sample paper1 markSemiconductors and temperature

From the two supplied ρ(T) plots, identify which is consistent with intrinsic Ge and which with ordinary copper in the stated temperature range.

Check answer
A, the decreasing curve, represents intrinsic Ge; B, the increasing curve, represents copper. These are qualitative sketches; the exact curvature alone is not a universal identification test.
Q2542022–23 · 2015–16Sample paperAdapted questionp–n junction and diode bias

A is an unbiased junction’s schematic potential-versus-position profile. B has a higher barrier and wider depletion transition; C has a lower barrier and narrower transition. Identify their bias.

Check answer
B is reverse bias; C is forward bias. Reverse bias increases barrier and depletion width; forward bias reduces both. The horizontal coordinate x is position, not “barrier width” as a separately swept independent quantity. The drawn ramps are schematic potential profiles, not exact solutions for abrupt junction charge distributions.
Q2582020–21Sample paper1 markDiode bias and I–V characteristics

Voltage rises from 0.70 V to 0.71 V and diode current increases by 10 mA. Find average dynamic resistance.

Check answer
r=ΔV/ΔI=0.01/0.010=1 Ω.
Q2602020–21Sample paper1 markRectifiers and filters

Find the ripple frequency of a half-wave rectifier for a 25 Hz sinusoidal input.

Check answer
25 Hz. A full-wave rectifier on the same source would give 50 Hz for equal successive pulses.
Q2632019–20Sample paper3 marksRectifiers and filters

Show one way to convert a four-diode full-wave bridge to half-wave rectification by disconnecting a diode branch. Draw the modified circuit and explain the surviving current path. Assume ideal diodes and a resistive load.

Check answer and diagram
Disconnect one bridge diode branch that belongs to only one of the two alternate conduction paths. That half-cycle then has no complete path; the opposite half-cycle still conducts through its two remaining forward diodes and the load. Keep the AC source and load across their original bridge diagonals. Do not short the AC source or simply short a diode across it.
Q2642018–19Sample paperAdapted questionSemiconductors and temperature

A resistance wire A and n-type semiconductor B have equal cross-section and are in series at constant current. (a) Compare electron drift speeds assuming B has a much lower conduction-electron density. (b) What happens to their voltage drops if they warm up? State any semiconductor-temperature assumption needed.

Check answer
(a) |v_d|=I/(neA), so the semiconductor has greater electron drift speed under the stated single-majority-carrier approximation. (b) The metal’s resistance and IR drop usually rise. The semiconductor’s trend is not fixed merely by “n-type”: in an intrinsic/thermally activated regime its resistance may fall, whereas in an extrinsic regime with nearly fixed n, reduced mobility can make it rise. Thermal and doping conditions are needed for a definite claim; continuous current alone does not specify temperatures.

Diagram

↑