Draw and label a step-up transformer; give its principle and derive voltage/turns/current ratios. Numerical: Np:Ns = 1:5, primary input 5 kW at 200 V; determine primary current and secondary voltage. Assume an ideal transformer and RMS primary voltage.
CBSE · Class 12 Physics · Chapter 7
Alternating Current PYQs
Chapter-wise board questions and sample-paper practice.
27 questions · 25 topics. Attempt each question before opening its available answer or diagram check.
Class 12 Physics · Chapter 7 · 27 questions · pyqhub.org
No questions match. Try another term or reset the filters.
Explain the usefulness of voltage transformation in AC power transmission. Assess the claim that AC is always less hazardous than DC, regardless of voltage, frequency and conditions of contact.
For V(t)=V₀ sin(ωt), state the RMS voltage and the mean voltage over one complete cycle.
For v(t)=v₀ sin(ωt) and i(t)=i₀ sin(ωt+φ), derive the average power over one complete cycle.
For I(t)=I₀ cos(100πt), find the shortest time interval from a current maximum to the next zero.
For a capacitor and an inductor in series with a variable-frequency AC source, identify whether the circuit is capacitive/inductive below and above resonance.
A capacitor has its capacitance doubled and source frequency tripled. Identify the resulting factor change in its capacitive reactance.
For a series R–L–C arrangement supplied by v = vₘ sin(ωt), derive mean power dissipation and the resonant-frequency expression. Discuss wattless current in a pure reactance. Separately, for a fixed RMS supply and fixed nonzero R, give the condition for maximum average power as reactance is varied.
Derive impedance of a series R–C circuit; explain when an inductor behaves as a conductor; find the series-coil inductance needed to operate a lamp rated 110 V DC, 11 A on 220 V, 50 Hz AC. Treat the lamp as a 10 Ω resistor at its operating temperature and the series inductor as lossless. Use RMS supply values.
Draw a labelled step-up transformer and explain mutual induction; identify three real-transformer losses; explain energy conservation; calculate output voltage and input current when Np=200, Ns=3000, Vp=90 V and secondary current is 2.0 A. Assume an ideal transformer for the numerical calculation. Explain why a steady DC input cannot maintain a secondary emf, and discuss four practical loss mechanisms.
Check answer and diagram
Two devices each draw 0.22 A at 220 V; one current lags by π/2 while the other is in phase. Identify the devices and calculate current when connected in series. Assume the phase relations describe an ideal inductor and an ideal resistor; 220 V and 0.22 A are RMS values at the same frequency.
For a resistor R and capacitor C connected in series across V=V₀ sin(ωt), determine the peak voltage across (i) R and (ii) C; find the phase difference between applied voltage and current and state which leads.
Supply the physical effect reduced by using laminated iron sheets in the core of a transformer.
Derive series LCR impedance and sketch its dependence on applied AC frequency; at resonance state the phase difference across L and C; for a coil carrying 1 A at 200 V DC but 0.5 A at 200 V, 50 Hz AC, explain the reduced current and find self-inductance. Use ideal L and C with total series resistance R, constant RMS supply voltage, and distinguish resistance from impedance. Sketch the current-amplitude resonance curve at fixed supply amplitude and identify the minimum-impedance and wattless conditions.
Check answer and diagram
Explain why a step-up transformer is used before long-distance AC transmission. At fixed delivered power P and line resistance R_line, derive the dependence of line heating loss on transmission voltage V. Assume unity power factor and neglect transformer losses.
Check answer
A device ‘X’ is connected to an AC source V = V₀ sin ωt. The variation of voltage, current and power in one cycle is shown in the graph. (a) Identify the device X. (b) Which of the curves A, B and C represent the voltage, current and power consumed in the circuit? Justify your answer. (c) How does its impedance vary with the frequency of the AC source? Show graphically. (d) Obtain an expression for the current in the circuit and its phase relation with the AC voltage.
Draw and explain an AC generator and derive the emf for an N-turn coil in B; then find instantaneous motional emf in a 10 m east–west rod falling at 5.0 m s⁻¹ perpendicular to Earth’s horizontal field 0.3×10⁻⁴ Wb m⁻². Assume the rod is perpendicular to the northward horizontal field. Also identify the mechanical source of energy in the generator.
Check diagram
Explain zero mean power in a pure capacitive AC circuit, and predict lamp brightness when capacitance in its series circuit is reduced.
For a pure ideal inductor connected across v(t)=V₀ sin(ωt), derive the steady-state current and show that it lags the voltage by π/2.
An incandescent lamp with negligible coil inductance is connected in series with a capacitor to an AC supply. Predict how lamp brightness responds to reducing (i) capacitance and (ii) frequency; explain.
Explain resonance in a series LCR circuit, express the resonant frequency and describe selection of a radio station with a variable-capacitance tuned circuit. Sketch the current–frequency response for fixed supply amplitude and nonzero series resistance.
Check answer and diagram
If the phasor diagram for a device connected to an AC supply is as shown, which of the following statements is true? (A) When the frequency of the AC source is increased, the impedance of the device decreases. (B) This device behaves as a conducting wire when connected across a DC source. (C) When the frequency of the AC source is decreased, the impedance of the device decreases. (D) This device stores energy in the form of magnetic potential energy.
Check answer
An AC generator initially produces v=V₀ sin(ωt). Write the new emf expression if its angular speed is doubled while its coil area, turn count and magnetic field remain unchanged.
Check answer
Ideal transformer with Nₚ=1000, Nₛ=100 and Vₚ=200 sin(100πt) V supplies a series load R=4 Ω, Xᴄ=2 Ω and Xᴸ=6 Ω. Determine secondary voltage, load current/power, plus transformer principle and transmission advantage.
Check answer
The RMS voltage across each of R, L and C in a series LCR circuit is 10 V. The ideal capacitor is shorted while the supply RMS voltage and frequency remain unchanged. Find the new RMS voltage across the ideal inductor.
- 10 V
- 10√2 V
- 10/√2 V
- 20 V
Check answer
State and illustrate a generator’s operating principle, derive instantaneous induced emf of an N-turn coil (area A, angular speed ω, uniform B), and identify mechanical energy input.
Check answer and diagram
Sketch inductive and capacitive reactance versus frequency and the LCR phasor diagram. Then use 220 V and 0.25 A for an inductive element (lag π/2) and a resistive element (in phase), and calculate series current.