Class 10 Science · Chapter 11 · 39 questions · pyqhub.org

E0012018Board examination3 marksAdapted questionSeries & parallel

Using three 9 Ω resistors, determine two connections that give equivalent resistances of (i) 13.5 Ω and (ii) 6 Ω. Draw the required combinations.

Check answer
(i) One 9 Ω resistor in series with a parallel pair of 9 Ω resistors: 9 + 4.5 = 13.5 Ω. (ii) Two 9 Ω resistors in series, with this 18 Ω branch parallel to the remaining 9 Ω: equivalent 6 Ω.
E0022018Board examination3 marksAdapted questionJoule heating & power

State Joule’s heating law. Two lamps rated 100 W, 220 V and 60 W, 220 V are connected in parallel to a 220 V supply. Determine the current through each lamp and the combined supply current.

Check answer
Heat H = I²Rt. Currents: 100/220 = 0.455 A; 60/220 = 0.273 A. Combined supply current = 160/220 ≈ 0.727 A.
E0032018Board examination3 marksAdapted questionResistance & resistivity

List the factors controlling the resistance of a wire. Explain why a metal conducts electricity well whereas glass does not, and give one reason alloys are chosen for electrical heaters.

Check answer
Resistance depends on length (directly), cross-sectional area (inversely), material/resistivity and temperature. Metals have mobile electrons/low resistivity; glass has high resistivity. Heating alloys have high resistivity or melting point and resist oxidation.
E0042018Board examination2 marksAdapted questionOhm’s law & V–I graph

A resistor gives the following readings. Plot I against V and obtain its resistance: V (V) = 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0; I (A) = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.8, 1.0.

Check answer and diagram
Graph: straight line passing through origin. R = ΔV/ΔI = (2.0 − 1.0)/(0.4 − 0.2) = 5 Ω.
E0052019Board examination5 marksAdapted questionParallel circuits

Explain/derive the equivalent resistance relation for three resistors in parallel using a circuit. For two 12 Ω resistors in parallel across 6 V, calculate the net current.

Check answer
By common V and current division, 1/Rp = 1/R₁ + 1/R₂ + 1/R₃. Two 12 Ω in parallel give Rp = 6 Ω and I = 6/6 = 1 A.
E0062019Board examination5 marksAdapted questionSeries circuits & power

(OR alternative of Q20) An electric lamp of resistance 20 Ω and a conductor of resistance 4 Ω are connected to a 6 V battery as shown in the circuit. Calculate : (a) the total resistance of the circuit, (b) the current through the circuit, (c) the potential difference across the (i) electric lamp and (ii) conductor, and (d) power of the lamp.

Check answer
Total resistance = 24 Ω; current = 6/24 = 0.25 A; lamp p.d. = 5 V; conductor p.d. = 1 V; lamp power = 5 × 0.25 = 1.25 W.
E0072019Board examination2 marksAdapted questionOhm’s law & V–I graph

Interpret the straight line obtained by plotting potential difference against current in an Ohm’s-law experiment. Explain the method of finding the resistance from the graph.

Check answer
Potential difference V ∝ current I at constant temperature. Calculate resistance from the slope ΔV/ΔI of a V-versus-I graph.
E0082020Board examination3 marksAdapted questionOhm’s law & instruments

A V-I graph for a nichrome wire is given below. What do you infer from this graph? Draw a labelled circuit diagram to obtain such a graph.

Check answer
At constant temperature V ∝ I. Ammeter in series; voltmeter across the resistor in parallel.
E0092020Board examination3 marksAdapted questionJoule heating & energy

Give the relation for heat generated by an electric current. Find the heat produced when 96,000 C of charge flows through a potential difference of 40 V.

Check answer
H = I²Rt = VIt = VQ. H = 40 × 96,000 = 3,840,000 J = 3.84 × 10⁶ J.
E0102022Board examination3 marksAdapted questionSeries & parallel

(a) Three resistors R₁, R₂ and R₃ are connected in parallel and the combination is connected to a battery, an ammeter, a voltmeter and a key. Draw suitable circuit diagram to show the arrangement of these circuit components along with the direction of current flowing. (b) Calculate the equivalent resistance of the following network :

Check answer
Two 10 Ω resistors in parallel give 5 Ω. With the remaining 5 Ω + 5 Ω series branches, total resistance is 15 Ω.
E0112022Board examination3 marksAdapted questionPower & parallel loads

Define electric power and state its SI unit. Two parallel lamps are rated 100 W, 220 V and 60 W, 220 V. At 220 V, find the total current from the supply.

Check answer
Electrical power is energy consumed per unit time; SI unit watt (J s⁻¹). I = 100/220 + 60/220 = 160/220 ≈ 0.73 A.
E0122022Board examination3 marksAdapted questionJoule heating

State Joule’s heating law and its dependence on current, resistance and time. A 5 Ω resistor is connected to 6 V for 10 s. Calculate the electrical energy dissipated as heat.

Check answer
H ∝ I², H ∝ R and H ∝ t; H = I²Rt = VIt. For V=6 V, R=5 Ω and t=10 s, heat = (V²/R)t = (36/5)×10 = 72 J.
E0132023Board examination1 markAdapted questionSeries & parallel

Four equal resistors of 8 Ω are connected all in series, then all in parallel. What is the ratio of the resulting series resistance to parallel resistance?

  1. 32
  2. 2
  3. 0.5
  4. 16
Check answer
16. Series 32 Ω, parallel 2 Ω, so Rs/Rp = 16.
E0142023Board examination1 markAdapted questionMeters & measurement

In the following diagram, the position of the needle is shown on the scale of a voltmeter. The least count of the voltmeter and the reading shown by it respectively are :

  1. 0.15 V and 1.6 V
  2. 0.05 V and 1.6 V
  3. 0.15 V and 1.8 V
  4. 0.05 V and 1.8 V
Check answer
Least count 0.15 V; indicated reading 1.8 V.
E0152023Board examination5 marksAdapted questionHeating & power

An iron draws 880 W on its highest setting and 330 W on its lowest, with a 220 V supply. Calculate current and resistance in both settings. Describe the heating effect and derive the heat equation.

Check answer
High: I=4 A, R=55 Ω. Low: I=1.5 A, R≈146.7 Ω. Current through a resistance converts electrical energy to heat; H = I²Rt.
E0162024Board examination2 marksAdapted questionSeries & parallel

Arrange three 6 Ω resistors so their resultant resistance is 9 Ω. Explain or draw the connection.

Check answer
Connect two 6 Ω resistors in parallel for 3 Ω; connect this in series with the third 6 Ω: total 9 Ω.
E0172024Board examination2 marksAdapted questionElectric power

(B) (OR alternative of Q25) Calculate the power used in the 2 Ω resistor in the given circuit :

Check answer
Resistances in series give 3 Ω. Circuit current = 6/3 = 2 A. Power in 2 Ω = I²R = 2² × 2 = 8 W.
E0182024Board examination5 marksAdapted questionElectrical power & energy

Define electric power and express it using potential difference and resistance. An oven uses 11 electrical units in 5 h on a 220 V supply: determine power, current and resistance.

Check answer
P = V²/R. Energy = 11 kWh in 5 h gives P = 2.2 kW = 2,200 W; I = 10 A; R = 22 Ω.
E0192024Board examination5 marksAdapted questionResistivity

Relate resistance to resistivity. A wire 3 m long has resistance 60 Ω and cross-section 4 × 10⁻⁷ m². Calculate resistivity. Explain what happens to resistivity when the wire is stretched to twice its original length.

Check answer
R = ρL/A, ρ = RA/L = (60 × 4 × 10⁻⁷)/3 = 8 × 10⁻⁶ Ω m. Resistivity stays unchanged for the same material at the same temperature.
E0202025Board examination2 marksAdapted questionSeries & parallel

A wire has resistance R. Cut it into three equal lengths and join the three sections in parallel. Determine the equivalent resistance.

Check answer
Each piece has R/3. Three such sections in parallel yield Req = R/9.
E0212025Board examination2 marksAdapted questionElectric power

Define electrical power and specify the condition under which a circuit consumes power at the rate of one watt.

Check answer
Power is the rate of electrical-energy consumption. 1 W = 1 J s⁻¹, equivalently 1 V × 1 A.
E0222025Board examination3 marksAdapted questionMixed resistor networks

Consider the following electric circuit : Calculate the values of the following : (a) The total resistance of the circuit (b) The total current drawn from the source (c) Potential difference across the parallel combination of 10 Ω and 15 Ω resistors

Check answer
Top group 10 Ω ∥ 15 Ω = 6 Ω; bottom group 60 Ω ∥ 40 Ω = 24 Ω. In series, total 30 Ω; supply current = 5/30 = 1/6 A (about 0.17 A); p.d. across the 10 Ω ∥ 15 Ω group = (1/6)×6 = 1 V. The battery printed on the figure is 5 V.
E0232025Board examination3 marksAdapted questionResistivity & heating alloys

State the resistance–resistivity relation and the SI unit of resistivity. Explain why alloys are preferred as the heating element of common appliances.

Check answer
R=ρL/A and SI unit Ω m. Heating alloys have greater resistivity and tend not to oxidise readily at high temperatures.
E0242026Board examination2 marksAdapted questionResistivity

A cylindrical conductor has radius 0.01 cm, length 1.0 cm and resistance 7 Ω. Calculate the resistivity of its material, converting all quantities into SI units.

Check answer
r=10⁻⁴ m, L=10⁻² m; ρ=Rπr²/L = 7π×10⁻⁸/10⁻² ≈ 2.2×10⁻⁵ Ω m.
E0252026Board examination2 marksAdapted questionElectric power

A heater takes 11 A at 220 V. Assuming its resistance does not change, find its power consumption when the voltage is reduced to 200 V.

Check answer
R = 220/11 = 20 Ω; P = 200²/20 = 2,000 W = 2 kW.
E0262026Board examination5 marksAdapted questionResistivity & current

Explain why wire dimensions change its resistance but not resistivity; justify use of alloys in toasters and irons; define the electric current of one ampere.

Check answer
R = ρL/A depends on dimensions; resistivity is material-dependent (at given temperature). Alloys have higher resistivity and/or resist oxidation at high temperature. 1 A = 1 C of charge flowing per second.
E0272026Board examination5 marksAdapted questionParallel loads & Joule heating

How many 8 Ω bulbs connected in parallel are needed to draw 2 A from 4 V? Name the measuring device for this current and its correct placement; state Joule’s law.

Check answer
Required total R=4/2=2 Ω; n identical 8 Ω resistances in parallel give 8/n = 2 ⇒ n=4. Use an ammeter connected in series. Joule’s law H=I²Rt.
E0282026Board examination1 markAdapted questionMeters & measurement

Select the correct connections of an ammeter and a voltmeter when measuring current through, and voltage across, a resistor.

  1. Ammeter parallel, voltmeter series
  2. Both parallel
  3. Ammeter series, voltmeter parallel
  4. Both series
E0292026Board examination3 marksAdapted questionOhm’s law & instruments

Identify devices used (i) to maintain potential difference and (ii) to vary current. A heater uses 5 A at 110 V; at unchanged resistance, calculate its current on 220 V.

Check answer
cell or battery maintains potential difference; a rheostat varies current. R = 110/5 = 22 Ω; at 220 V, I = 220/22 = 10 A.
E0302026Board examination3 marksAdapted questionMixed resistor networks

Consider the given electric circuit : Calculate the following : (a) Total resistance of the circuit (b) The electric current drawn from the battery (c) Potential difference between points P and Q

Check answer
Between R and S: (4 + 1) Ω in parallel with 5 Ω gives 2.5 Ω. Between P and Q: (2 + 3) Ω in parallel with 5 Ω gives 2.5 Ω. These groups are in series: total 5 Ω; battery current 10/5 = 2 A; V_PQ = 2 × 2.5 = 5 V.
E0312026Board examination3 marksAdapted questionOhm’s law & V–I graph

Plot a V–I graph and infer resistance from readings: I (A) = 0.4, 0.8, 1.2, 1.6, 2.0; V (V) = 1.2, 2.4, 3.6, 4.8, 6.0.

Check answer and diagram
The V-against-I graph is a straight line through the origin. R = ΔV/ΔI = 1.2/0.4 = 3 Ω, constant for all readings.
E0322026Board examination4 marksAdapted questionHeating & energy

Explain why a working refrigerator releases heat to its surroundings. Derive Joule’s law H = I²Rt for a resistor.

Check answer
refrigerator transfers heat from its cooled interior to the room; the electrical work supplied also ends up as heat, so heat expelled exceeds heat removed. For a resistor, H = VQ = VIt; using V = IR gives H = I²Rt.
E0332026Board examination3 marksAdapted questionSeries & parallel

Explain why a bulb may become dimmer when an electric heater on the parallel branch is switched on. Arrange three 8 Ω resistors to obtain 12 Ω, with a suitable circuit sketch.

Check answer
With ideal constant-voltage parallel supply the bulb would not dim. Real supply wiring has resistance: the extra heater current increases the voltage drop in it, lowering the bulb voltage. For 12 Ω, put two 8 Ω resistors in parallel (4 Ω) and the third 8 Ω in series.
E0342026Board examination4 marksAdapted questionResistance & resistivity

In an Ohm’s-law activity, three students use nichrome wires of length L and 2L and a copper wire of length L (equal cross-section). Predict the effects on current when nichrome length doubles or its cross-sectional area doubles; explain the role of material/resistivity.

E0352026–27 SQPSample paper1 markAdapted questionCurrent & power

A 1,000 W appliance is rated for 250 V. Calculate the current under rated operation.

  1. 0.25 A
  2. 2.5 A
  3. 4.0 A
  4. 10 A
Check answer
4.0 A, using I = P/V.
E0362026–27 SQPSample paper2 marksAdapted questionJoule heating

Give Joule’s heating law and state how generated heat changes if resistance doubles while current and duration remain the same.

Check answer
H=I²Rt. Doubling R while I and t are fixed doubles H.
E0372026–27 SQPSample paper2 marksAdapted questionResistivity

Define electrical resistivity, give its SI unit, and explain why wires of the same substance with different dimensions share one resistivity at fixed temperature.

Check answer
ρ=RA/L; SI unit Ω m. It is intrinsic to the material at a specified temperature.
E0382026–27 SQPSample paper3 marksAdapted questionMixed resistor networks

The figure shows a circuit with a 15 V battery connected to several resistors. Using the given circuit diagram: A. Find the total current supplied by the battery. B. Calculate the potential difference between points A and B.

Check answer
Equivalent total resistance = 7.5 Ω; I = 15/7.5 = 2 A; V_AB = 2 V.
E0392026–27 SQPSample paper3 marksAdapted questionSeries circuits

In a series circuit powered by 15 V, resistors measure 2 Ω, 3 Ω and 5 Ω. Determine combined resistance, total current and voltage drop across 3 Ω.

Check answer
Req=2+3+5 = 10 Ω; I=15/10 = 1.5 A; V₃Ω=1.5×3=4.5 V.

Diagram

↑