Class 10 Science · Chapter 12 · 48 questions · pyqhub.org

MAG-0012019Board examination5 marksAdapted questionSolenoids & electromagnets

Define a solenoid; sketch the magnetic fields for (i) a current-carrying solenoid and (ii) a permanent bar magnet. Identify two differences between those fields.

Check answer
A solenoid is a long coil of closely wound insulated wire. Its external field resembles a bar magnet and the field inside is approximately uniform. Unlike a permanent magnet, its field can be switched off, varied by changing current, and reversed by reversing current (any two differences). Field lines go north to south outside and return south to north inside.
MAG-0022020Board examination1 markAdapted questionDomestic wiring & safety

What happens to the current during a short circuit in a domestic circuit? Explain.

Check answer
The resistance of the fault path becomes very small, causing a very large current. A correctly rated protective device interrupts the circuit.
MAG-0032020Board examination5 marksAdapted questionSolenoids & electromagnets

Explain what an electromagnet is, draw its construction using a soft-iron core and coil, explain the core’s purpose, and give two ways to make it stronger.

Check answer
When current flows through a solenoid containing a soft-iron core, the core becomes a temporary magnet. Suitable uses include an electric bell. The soft-iron core strengthens the field; increased current or more turns strengthens it further.
MAG-0042022Board examination2 marksAdapted questionForce on conductors

State Fleming’s left-hand rule. An electron moves upward on the page through a magnetic field directed to the right. Determine the magnetic force direction.

Check answer
Hold the left thumb, forefinger and middle finger mutually perpendicular: forefinger points along field, middle finger along conventional current, thumb along force. For an upward-moving electron and rightward field, force is out of the page.
MAG-0052022Board examination4 marksAdapted questionMagnetic field lines

A bar magnet is placed under a sheet sprinkled with iron filings. Draw the resulting pattern and field-line directions. Explain why field lines never cross, or describe tracing field lines using a compass.

MAG-0062023Board examination1 markAdapted questionDomestic wiring & safety

Which needs the higher-current domestic circuit in the textbook model: a room heater, ceiling fan or LED lamp? Explain.

Check answer
Room heater: its much greater power requires more current at the same voltage, I = P/V.
MAG-0072023Board examination1 markMagnetic fields of conductors

The resultant magnetic field at point ‘P’ situated midway between two parallel wires (placed horizontally) each carrying a steady current I is (a) in the same direction as the current in the wires. (b) in the vertically upward direction. (c) zero (d) in the vertically downward direction.

MAG-0082023Board examination1 markAdapted questionCircular coils

Assertion: For a circular coil of fixed radius and current, the magnetic field at its centre increases with its number of turns. Reason: The fields produced by individual turns add in the same direction. Evaluate the pair.

Check answer
Both true; the reason explains the assertion.
MAG-0092023Board examination3 marksForce on conductors

(a) (i) State the rule used to find the force acting on a current carrying conductor placed in a magnetic field. (ii) Given below are three diagrams showing entry of an electron in a magnetic field. Identify the case in which the force will be (1) maximum and (2) minimum respectively. Give reason for your answer.

MAG-0102024Board examination1 markSolenoids & electromagnets

The pattern of the magnetic field produced inside a current carrying solenoid is : (a) (b) (c) (d) [options are the four drawings in the figure]

MAG-0112024Board examination2 marksAdapted questionMagnetic field lines

Explain why magnetic field lines cannot intersect. Illustrate how a region with uniform magnetic field is represented.

MAG-0122024Board examination3 marksAdapted questionHand rules

Name and state (i) the rule for the field around a straight conductor and (ii) the rule for force on a perpendicular current-carrying wire.

MAG-0132024Board examination3 marksAdapted questionMagnetic field lines

Describe what iron filings around a bar magnet reveal, why they crowd near its ends, and what their arrangement around a current-carrying solenoid would show.

MAG-0142025Board examination1 markAdapted questionMagnetic field lines

Assess the statement that magnetic field lines do not intersect and the explanation involving a compass needle having only one direction at a point.

MAG-0152025Board examination1 markAdapted questionDomestic wiring & safety

State the live, neutral and earth insulation colours used in the traditional NCERT domestic-wiring description.

Check answer
Live red, neutral black, earth green in the traditional NCERT convention. Modern harmonised installations may use brown, blue and green/yellow; wire colour alone must never be used to establish that a circuit is safe.
MAG-0162025Board examination1 markAdapted questionDomestic wiring & safety

For an electric iron of 1 kW powered at 220 V, calculate its current requirement and choose an appropriate domestic-circuit current rating.

MAG-0172025Board examination2 marksAdapted questionDomestic wiring & safety

Explain the protective role of the earth wire, especially for metallic-bodied appliances such as electric irons.

MAG-0182025Board examination2 marksAdapted questionDomestic wiring & safety

State two precautions used in household wiring to avoid electrical accidents, and explain how they protect people or appliances.

MAG-0192025Board examination5 marksHand rules

(a) The given figure shows the current passing through the straight conductor XY. (i) Copy the diagram and draw the magnetic field lines when current flows from conductor X to Y. (ii) Name and state the rule used in determining the direction of the magnetic field lines in the situation given above. (iii) State Fleming’s left hand rule. Using this rule, determine the direction of force applied on an electron entering a uniform magnetic field as shown in the figure.

MAG-0202025Board examination5 marksAdapted questionSolenoids & electromagnets

Define a solenoid and draw its field pattern, marking current direction, field directions near its ends and the approximately uniform region. Explain creating an electromagnet with it.

MAG-0212026Board examination3 marksAdapted questionForce on conductors

Describe an experiment demonstrating force on a current-carrying conductor in a magnetic field. State what happens on reversing the current or the field.

Check answer
Suspend a conducting rod freely between magnet poles and pass a current through it: the rod is displaced. Reversing current alone or field alone reverses force. Reversing both leaves force direction unchanged.
MAG-0222026Board examination3 marksMagnetic fields of conductors

(a) The pattern of magnetic field due to a current carrying wire depends upon the shape made by that wire. Justify. (b) A current carrying straight wire AB is shown in the given diagram. Out of X, Y and Z on which point will the strength of magnetic field be maximum and why ?

MAG-0232026Board examination1 markAdapted questionSolenoids & electromagnets

Choose which listed claims about a battery-connected solenoid are correct: its field resembles a bar magnet, its poles can be determined by a hand rule, and it can magnetise a soft-iron core.

Check answer
All three stated claims are correct: a solenoid resembles a bar magnet, its polarity follows the right-hand grip rule, and it can magnetise a soft-iron core.
MAG-0242026Board examination2 marksAdapted questionCircular coils

Draw the magnetic field of a current-carrying circular loop and name the factors that control the field magnitude of a coil.

Check answer
The field lines around each part of the loop combine; near the centre they are approximately parallel and along the loop axis. For fixed geometry the field increases with current and number of turns, and decreases as coil radius increases. Use the right-hand grip rule for direction.
MAG-0252026Board examination3 marksAdapted questionDomestic wiring & safety

In household wiring, describe the job of a fuse versus the green-coloured earth wire; predict the risk when an incorrectly high fuse rating is used.

MAG-0262026–27 SQPSample paper3 marksAdapted questionHand rules

Describe how the right-hand thumb rule determines magnetic-field direction for a straight current-carrying wire; state how the field magnitude varies with distance.

Check answer
Grasp the wire in the right hand with thumb along the conventional current; curled fingers show the circular field-line direction. For a straight conductor, field magnitude decreases as distance from the conductor increases (inverse dependence).
MAG-0272026–27 SQPSample paper4 marksAdapted questionSolenoids & electromagnets

A current-carrying solenoid with a soft-iron core lifts a bolt. Explain the core’s effect. How do you identify the solenoid’s poles from the current viewed at either end? What happens if current doubles with geometry fixed? Give another way to strengthen it.

Check answer
The core is magnetised and strengthens the field. Anticlockwise current viewed from an end makes that end north; clockwise makes it south. At fixed geometry, doubling current approximately doubles the field (before core saturation). Increase turns per unit length to strengthen it.
MAG-0282025–26 SQPSample paper3 marksMagnetic field lines

Magnetic field lines are shown in the given diagram. A student makes a statement that the magnetic field at X is stronger than at Y. (i) Explain with reason if the student’s claim is correct. (ii) Also redraw the diagram and mark the direction of magnetic field lines.

Check answer
Crowded field lines indicate stronger field; field at X (near the pole) is greater than at Y. Outside a magnet, arrows run from N to S.
MAG-0292024–25 SQPSample paper3 marksMagnetic fields of conductors

Mona was doing an experiment with a magnetic compass and a straight current-carrying wire. She observed that as she moved the compass away from the current-carrying wire, the deflection of the compass needle reduced. A. Explain why the deflection of the compass needle reduced as Mona moved away the compass needle from the current carrying wire. B. Mention one thing that could have changed in the circuit of the wire that could increase the deflection of the needle. C. Explain with reason what will be the direction of the magnetic field associated with the wire for the case described by the above figure.

Check answer
The field weakens with distance, reducing compass deflection. Increase current to strengthen the field. In the supplied diagram the positive battery terminal feeds the top connection, so current in the straight wire passes downward through the board; viewed from above, field lines run clockwise by the right-hand thumb rule.
MAG-0302024–25 SQPSample paper2 marksAdapted questionDomestic wiring & safety

For a room heater rated 1000 W at 220 V, select between fuse wires rated 2 A and 5 A and justify.

Check answer
I = P/V = 1000/220 ≈ 4.55 A; a 5 A fuse is appropriate rather than a 2 A fuse.
MAG-0312023–24 SQPSample paper1 markAdapted questionMagnetic fields of conductors

Assess an assertion claiming compass deflection falls when current increases and a reason stating that magnetic field is stronger for larger current.

Check answer
assertion false; reason true.
MAG-0322023–24 SQPSample paper2 marksMagnetic field lines

(OR alternative of Q25) Refer to the image below and state how the magnetic field pattern indicates regions where the magnetic field is stronger outside the magnet? What happens to the magnetic field when the current in the circuit is reversed?

Check answer
The field is stronger wherever lines are closer together, normally near the poles. Reversing current reverses the magnetic-field direction.
MAG-0332023–24 SQPSample paper3 marksAdapted questionDomestic wiring & safety

Evaluate the claim that a three-pin plug is used mainly to reduce heating; explain why metallic appliances need earthing, and state the purpose of a fuse.

Check answer
The claim is incorrect. The third pin provides earthing, a low-resistance path for fault current to protect users from shock. A fuse melts when current exceeds its safe rating, breaking the circuit.
MAG-0342022–23 SQPSample paper1 markAdapted questionMagnetic fields of conductors

Describe the shape of magnetic field lines around a long, straight current-carrying wire.

Check answer
Concentric circles centred on the wire, in planes perpendicular to it; direction follows the right-hand thumb rule.
MAG-0352022–23 SQPSample paper3 marksAdapted questionMagnetic field lines

A bar magnet is placed beneath evenly sprinkled iron filings. Why do filings form a pattern? Which field feature is shown? State two properties of magnetic field lines.

Check answer
Each filing gets magnetised and aligns with the local field. The pattern shows field direction and relative strength. Field lines form closed continuous curves, do not intersect, and outside a bar magnet go from north to south (any two appropriate properties).
MAG-0362022–23 SQPSample paper3 marksAdapted questionMagnetic fields of conductors

For a compass near a current-carrying wire, explain what happens to deflection when the current is increased and when the compass is moved farther away.

Check answer
Increasing the current strengthens the magnetic field and increases deflection. Moving the compass away weakens the field and reduces deflection.
MAG-0372022–23 SQPSample paper5 marksDomestic wiring & safety

The diagram above is a schematic diagram of a household circuit. The house shown in the above diagram has 5 usable spaces where electrical connections are made. For this house, the mains have a voltage of 220 V and the net current coming from the mains is 22A. (a) What is the mode of connection to all the spaces in the house from the mains? (b) The spaces 5 and 4 have the same resistance and spaces 3 and 2 have respective resistances of 20Ω and 30Ω. Space 1 has a resistance double that of space 5. What is the net resistance for space 5. (c) What is the current in space 3? (d) What should be placed between the main connection and the rest of the house’s electrical appliances to save them from accidental high electric current?

Check answer
Parallel. (b) Net resistance of the house = 220 V ÷ 22 A = 10 Ω. With R₅ = R₄ = R, R₃ = 20 Ω, R₂ = 30 Ω, R₁ = 2R: 1/10 = 1/R + 1/R + 1/20 + 1/30 + 1/(2R) ⇒ 1/60 = 2.5/R ⇒ R₅ = 150 Ω. (c) Each space gets the full 220 V, so I₃ = 220/20 = 11 A. (d) A fuse (or MCB).
MAG-0382021–22 SQPSample paper2 marksSolenoids & electromagnets

(OR alternative of Q6) A circuit contains a battery, a variable resistor and a solenoid. The figure below shows the magnetic field pattern produced by the current in the solenoid. a. State how the magnetic field pattern indicates regions where the magnetic field is stronger. b. What happens to the magnetic field when the current in the circuit is reversed?

Check answer
The field is strongest where lines crowd. Reversing current reverses the field and swaps the solenoid’s magnetic poles.
MAG-0392020–21 SQPSample paper1 markAdapted questionMagnetic fields of conductors

Draw the magnetic field lines around a straight conductor carrying current. Indicate their circular character and direction.

Check answer
Concentric circular field lines around the conductor, with direction established by the right-hand thumb rule.
MAG-0402020–21 SQPSample paper1 markAdapted questionSolenoids & electromagnets

What happens to a soft-iron bar placed inside a solenoid carrying current?

Check answer
It becomes magnetised and increases the magnetic field. It largely loses its magnetism when current stops.
MAG-0412020–21 SQPSample paper1 markAdapted questionSolenoids & electromagnets

Which familiar permanent magnet has a field pattern similar to a current-carrying solenoid?

Check answer
bar magnet.
MAG-0422020–21 SQPSample paper1 markAdapted questionSolenoids & electromagnets

How does magnetic field strength inside a solenoid depend on current when its geometry and core conditions are unchanged?

Check answer
It is approximately directly proportional to current, before magnetic-core saturation.
MAG-0432020–21 SQPSample paper1 markAdapted questionSolenoids & electromagnets

Read the passage and answer the graph question below. A solenoid is a long helical coil of wire through which a current is run in order to create a magnetic field. The magnetic field of the solenoid is the superposition of the fields due to the current through each coil. It is nearly uniform inside the solenoid and close to zero outside and is similar to the field of a bar magnet having a north pole at one end and a south pole at the other depending upon the direction of current flow. The magnetic field produced in the solenoid is dependent on a few factors such as, the current in the coil, number of turns per unit length etc. The following graph is obtained by a researcher while doing an experiment to see the variation of the magnetic field with respect to the current in the solenoid. The unit of magnetic field as given in the graph attached is in milli-Tesla (mT) and the current is given in Ampere. 20 (v) From the graph deduce which of the following statements is correct. a. For a current of 0.8A the magnetic field is 13 mT b. For larger currents, the magnetic field increases non-linearly. c. For a current of 0.8A the magnetic field is 1.3 mT d. There is not enough information to find the magnetic field corresponding to 0.8A current.

Check answer
Approximately 13 mT at 0.8 A: choice a. The graph is approximately linear through the origin.
MAG-0442020–21 SQPSample paper1 markAdapted questionSolenoids & electromagnets

In a linear-solenoid actuator, a current-carrying coil pulls a movable iron plunger. State the main useful energy conversion.

Check answer
Electrical energy to mechanical energy; a magnetic field provides the force moving the plunger. Some energy is also dissipated as heat.
MAG-0452019–20 SQPSample paper1 markAdapted questionDomestic wiring & safety

Assertion: A protective fuse should be connected in parallel with the main line. Reason: A fuse melts when current exceeds its specified safe value. Evaluate the statements.

Check answer
Assertion false; reason true. The fuse is connected in series in the live conductor so that melting interrupts the circuit.
MAG-0462019–20 SQPSample paper3 marksAdapted questionDomestic wiring & safety

A two-room home needs a living-room bulb, fan, refrigerator and a socket for appliances rated up to 2 kilowatt. Draw the household circuit with a safety fuse and earthing.

Check answer
Connect the bulb, fan, refrigerator and appliance socket in parallel between live and neutral. Put the main switch and correctly rated fuse/MCB in the live conductor before the branches. Connect protective earth to exposed metal cases and the earth terminal of the socket; earth must not carry normal operating current.
MAG-0472016–17 SQPSample paper5 marksAdapted questionMagnetic fields of conductors

Describe a labelled activity for observing the field around a long, straight current-carrying wire and name the direction rule. Compare the fields due to charge motion of a moving alpha particle and a moving neutron.

Check answer
Pass a straight wire vertically through cardboard and connect a battery, switch and rheostat in series. Sprinkle iron filings and tap gently: concentric circles form. Use the right-hand thumb rule. An alpha particle has charge and produces a field due to its motion; a neutron has no charge-motion contribution (it does have an intrinsic magnetic moment).
MAG-0482016–17 SQPSample paper3 marksAdapted questionDomestic wiring & safety

In the traditional NCERT domestic-wiring model, explain the purpose of earthing and what causes a short circuit. State the circuit ratings used for (a) lights and fans and (b) high-power appliances.

Check answer
Earthing provides a low-resistance fault path to protect against shock. Direct contact between live and neutral creates a low-resistance short circuit. The traditional textbook circuit ratings are 5 A for lights/fans and 15 A for high-power appliances; real protection must be selected for the wiring and load.

Diagram

↑